This right hand chute door fits standard laundry and trash chute intakes. The unit hinges on the side, so it opens toward the right hand. Therefore it works well for new installs and for direct swaps of worn units.

No. 4 finish stainless steel forms the body. A border trim frames the opening. Also, the face shows no exposed welds or solder seams, so staff can wipe it clean in seconds. The front uses 20 gauge steel, while the back steps up to a heavier 18 gauge for strength, and we build every door in the USA.

Features Of This Intake Unit

Users open this unit by hand, and it then closes on its own. A keyed-alike cylinder lock secures it, while the latch holds it shut. Because the latch grabs each time, the panel stays closed after every use. Additionally, silent operation keeps hallway noise down.

Fire Rating

This panel carries a UL label, so it meets fire code needs. In fact, it holds a 1.5 hour rating with a UL Class B label at 250°F maximum temperature rise. In addition, our doors meet the latest national building codes, plus NFPA-82 and ASTM standards. However, you should always follow the manufacturer instructions and your local fire code when you install or service it.

Specifications For This Right Hand Chute Door

Overall dimensions for this side hinged intake door. Measure the cut-out in the chute wall, not the door panel and not the trim.

The stainless body resists rust and daily wear, and the keyed alike cylinder means one key opens every matching door on the same job. Full specifications are listed in the Additional information tab above.

Not sure this is your size? Run our free trash chute door fit check or call 203-304-9000 before you order.

References: MB2121, 2121SH, SH2121, SHU2121

Order This Right Hand Chute Door

Do you need help confirming fit? First, our team checks your opening size and hinge side. Then we guide your order. So call us at 203-304-9000 and we will help you pick the right part quickly.

This door replaces Midland, US Chutes, and Wilkinson Hi-Rise chute doors. We also build custom solutions for Acme Chutes, American Chute Systems, Century Chutes, Chutes International, Cutler Chutes, Hi-Rise Recycling Systems, Midland Metalcraft, Valiant Chutes, and Western Chutes. Simply contact us with your measurements for a custom quote.

The post 21″ x 21″ Right Hand – Side Hinged (SH) Chute Intake Door appeared first on Action Chutes.

This right hand chute door fits standard laundry and trash chute intakes. The unit hinges on the side, so it opens toward the right hand. Therefore it works well for new installs and for direct swaps of worn units.

No. 4 finish stainless steel forms the body. A border trim frames the opening. Also, the face shows no exposed welds or solder seams, so staff can wipe it clean in seconds. The front uses 20 gauge steel, while the back steps up to a heavier 18 gauge for strength, and we build every door in the USA.

Features Of This Intake Unit

Users open this unit by hand, and it then closes on its own. A keyed-alike cylinder lock secures it, while the latch holds it shut. Because the latch grabs each time, the panel stays closed after every use. Additionally, silent operation keeps hallway noise down.

Fire Rating

This panel carries a UL label, so it meets fire code needs. In fact, it holds a 1.5 hour rating with a UL Class B label at 250°F maximum temperature rise. In addition, our doors meet the latest national building codes, plus NFPA-82 and ASTM standards. However, you should always follow the manufacturer instructions and your local fire code when you install or service it.

Specifications For This Right Hand Chute Door

Overall dimensions for this side hinged intake door. Measure the cut-out in the chute wall, not the door panel and not the trim.

The stainless body resists rust and daily wear, and the keyed alike cylinder means one key opens every matching door on the same job. Full specifications are listed in the Additional information tab above.

Not sure this is your size? Run our free trash chute door fit check or call 203-304-9000 before you order.

References: MB1818, 1818SH, SH1818, SHU1818

Order This Right Hand Chute Door

Do you need help confirming fit? First, our team checks your opening size and hinge side. Then we guide your order. So call us at 203-304-9000 and we will help you pick the right part quickly.

This door replaces Midland, US Chutes, and Wilkinson Hi-Rise chute doors. We also build custom solutions for Acme Chutes, American Chute Systems, Century Chutes, Chutes International, Cutler Chutes, Hi-Rise Recycling Systems, Midland Metalcraft, Valiant Chutes, and Western Chutes. Simply contact us with your measurements for a custom quote.

The post 18″ x 18″ Right Hand – Side Hinged (SH) Chute Intake Door appeared first on Action Chutes.

This left hand chute door fits standard laundry and trash chute intakes. The unit hinges on the side, so it opens toward the left hand. Therefore it works well for new installs and for direct swaps of worn units.

No. 4 finish stainless steel forms the body. A border trim frames the opening. Also, the face shows no exposed welds or solder seams, so staff can wipe it clean in seconds. The front uses 20 gauge steel, while the back steps up to a heavier 18 gauge for strength, and we build every door in the USA.

Features Of This Intake Unit

Users open this unit by hand, and it then closes on its own. A keyed-alike cylinder lock secures it, while the latch holds it shut. Because the latch grabs each time, the panel stays closed after every use. Additionally, silent operation keeps hallway noise down.

Fire Rating

This panel carries a UL label, so it meets fire code needs. In fact, it holds a 1.5 hour rating with a UL Class B label at 250°F maximum temperature rise. In addition, our doors meet the latest national building codes, plus NFPA-82 and ASTM standards. However, you should always follow the manufacturer instructions and your local fire code when you install or service it.

Specifications For This Left Hand Chute Door

Overall dimensions for this side hinged intake door. Measure the cut-out in the chute wall, not the door panel and not the trim.

The stainless body resists rust and daily wear, and the keyed alike cylinder means one key opens every matching door on the same job. Full specifications are listed in the Additional information tab above.

Not sure this is your size? Run our free trash chute door fit check or call 203-304-9000 before you order.

References: MB1818, 1818SH, SH1818, SHU1818

Order This Left Hand Chute Door

Do you need help confirming fit? First, our team checks your opening size and hinge side. Then we guide your order. So call us at 203-304-9000 and we will help you pick the right part quickly.

This door replaces Midland, US Chutes, and Wilkinson Hi-Rise chute doors. We also build custom solutions for Acme Chutes, American Chute Systems, Century Chutes, Chutes International, Cutler Chutes, Hi-Rise Recycling Systems, Midland Metalcraft, Valiant Chutes, and Western Chutes. Simply contact us with your measurements for a custom quote.

The post 18″ x 18″ Left Hand – Side Hinged (SH) Chute Intake Door appeared first on Action Chutes.

This right hand chute door fits standard laundry and trash chute intakes. The unit hinges on the side, so it opens toward the right hand. Therefore it works well for new installs and for direct swaps of worn units.

No. 4 finish stainless steel forms the body. A border trim frames the opening. Also, the face shows no exposed welds or solder seams, so staff can wipe it clean in seconds. The front uses 20 gauge steel, while the back steps up to a heavier 18 gauge for strength, and we build every door in the USA.

Features Of This Intake Unit

Users open this unit by hand, and it then closes on its own. A keyed-alike cylinder lock secures it, while the latch holds it shut. Because the latch grabs each time, the panel stays closed after every use. Additionally, silent operation keeps hallway noise down.

Fire Rating

This panel carries a UL label, so it meets fire code needs. In fact, it holds a 1.5 hour rating with a UL Class B label at 250°F maximum temperature rise. In addition, our doors meet the latest national building codes, plus NFPA-82 and ASTM standards. However, you should always follow the manufacturer instructions and your local fire code when you install or service it.

Specifications For This Right Hand Chute Door

Overall dimensions for this side hinged intake door. Measure the cut-out in the chute wall, not the door panel and not the trim.

The stainless body resists rust and daily wear, and the keyed alike cylinder means one key opens every matching door on the same job. Full specifications are listed in the Additional information tab above.

Not sure this is your size? Run our free trash chute door fit check or call 203-304-9000 before you order.

References: MB2424, 2424SH, SH2424, SHU2424

Order This Right Hand Chute Door

Do you need help confirming fit? First, our team checks your opening size and hinge side. Then we guide your order. So call us at 203-304-9000 and we will help you pick the right part quickly.

This door replaces Midland, US Chutes, and Wilkinson Hi-Rise chute doors. We also build custom solutions for Acme Chutes, American Chute Systems, Century Chutes, Chutes International, Cutler Chutes, Hi-Rise Recycling Systems, Midland Metalcraft, Valiant Chutes, and Western Chutes. Simply contact us with your measurements for a custom quote.

The post 24″ x 24″ Right Hand – Side Hinged (SH) Chute Intake Door appeared first on Action Chutes.

This left hand chute door fits standard laundry and trash chute intakes. The unit hinges on the side, so it opens toward the left hand. Therefore it works well for new installs and for direct swaps of worn units.

No. 4 finish stainless steel forms the body. A border trim frames the opening. Also, the face shows no exposed welds or solder seams, so staff can wipe it clean in seconds. The front uses 20 gauge steel, while the back steps up to a heavier 18 gauge for strength, and we build every door in the USA.

Features Of This Intake Unit

Users open this unit by hand, and it then closes on its own. A keyed-alike cylinder lock secures it, while the latch holds it shut. Because the latch grabs each time, the panel stays closed after every use. Additionally, silent operation keeps hallway noise down.

Fire Rating

This panel carries a UL label, so it meets fire code needs. In fact, it holds a 1.5 hour rating with a UL Class B label at 250°F maximum temperature rise. In addition, our doors meet the latest national building codes, plus NFPA-82 and ASTM standards. However, you should always follow the manufacturer instructions and your local fire code when you install or service it.

Specifications For This Left Hand Chute Door

Overall dimensions for this side hinged intake door. Measure the cut-out in the chute wall, not the door panel and not the trim.

The stainless body resists rust and daily wear, and the keyed alike cylinder means one key opens every matching door on the same job. Full specifications are listed in the Additional information tab above.

Not sure this is your size? Run our free trash chute door fit check or call 203-304-9000 before you order.

References: MB2424, 2424SH, SH2424, SHU2424

Order This Left Hand Chute Door

Do you need help confirming fit? First, our team checks your opening size and hinge side. Then we guide your order. So call us at 203-304-9000 and we will help you pick the right part quickly.

This door replaces Midland, US Chutes, and Wilkinson Hi-Rise chute doors. We also build custom solutions for Acme Chutes, American Chute Systems, Century Chutes, Chutes International, Cutler Chutes, Hi-Rise Recycling Systems, Midland Metalcraft, Valiant Chutes, and Western Chutes. Simply contact us with your measurements for a custom quote.

The post 24″ x 24″ Left Hand – Side Hinged (SH) Chute Intake Door appeared first on Action Chutes.

This left hand chute door fits standard laundry and trash chute intakes. The unit hinges on the side, so it opens toward the left hand. Therefore it works well for new installs and for direct swaps of worn units.

No. 4 finish stainless steel forms the body. A border trim frames the opening. Also, the face shows no exposed welds or solder seams, so staff can wipe it clean in seconds. The front uses 20 gauge steel, while the back steps up to a heavier 18 gauge for strength, and we build every door in the USA.

Features Of This Intake Unit

Users open this unit by hand, and it then closes on its own. A keyed-alike cylinder lock secures it, while the latch holds it shut. Because the latch grabs each time, the panel stays closed after every use. Additionally, silent operation keeps hallway noise down.

Fire Rating

This panel carries a UL label, so it meets fire code needs. In fact, it holds a 1.5 hour rating with a UL Class B label at 250°F maximum temperature rise. In addition, our doors meet the latest national building codes, plus NFPA-82 and ASTM standards. However, you should always follow the manufacturer instructions and your local fire code when you install or service it.

Specifications For This Left Hand Chute Door

Overall dimensions for this side hinged intake door. Measure the cut-out in the chute wall, not the door panel and not the trim.

The stainless body resists rust and daily wear, and the keyed alike cylinder means one key opens every matching door on the same job. Full specifications are listed in the Additional information tab above.

Not sure this is your size? Run our free trash chute door fit check or call 203-304-9000 before you order.

References: MB2121, 2121SH, SH2121, SHU2121

Order This Left Hand Chute Door

Do you need help confirming fit? First, our team checks your opening size and hinge side. Then we guide your order. So call us at 203-304-9000 and we will help you pick the right part quickly.

This door replaces Midland, US Chutes, and Wilkinson Hi-Rise chute doors. We also build custom solutions for Acme Chutes, American Chute Systems, Century Chutes, Chutes International, Cutler Chutes, Hi-Rise Recycling Systems, Midland Metalcraft, Valiant Chutes, and Western Chutes. Simply contact us with your measurements for a custom quote.

The post 21″ x 21″ Left Hand – Side Hinged Intake Door Blank Trim appeared first on Action Chutes.

This right hand chute door fits standard laundry and trash chute intakes. The unit hinges on the side, so it opens toward the right hand. Therefore it works well for new installs and for direct swaps of worn units.

No. 4 finish stainless steel forms the body. A border trim frames the opening. Also, the face shows no exposed welds or solder seams, so staff can wipe it clean in seconds. The front uses 20 gauge steel, while the back steps up to a heavier 18 gauge for strength, and we build every door in the USA.

Features Of This Intake Unit

Users open this unit by hand, and it then closes on its own. A keyed-alike cylinder lock secures it, while the latch holds it shut. Because the latch grabs each time, the panel stays closed after every use. Additionally, silent operation keeps hallway noise down.

Fire Rating

This panel carries a UL label, so it meets fire code needs. In fact, it holds a 1.5 hour rating with a UL Class B label at 250°F maximum temperature rise. In addition, our doors meet the latest national building codes, plus NFPA-82 and ASTM standards. However, you should always follow the manufacturer instructions and your local fire code when you install or service it.

Specifications For This Right Hand Chute Door

Overall dimensions for this side hinged intake door. Measure the cut-out in the chute wall, not the door panel and not the trim.

The stainless body resists rust and daily wear, and the keyed alike cylinder means one key opens every matching door on the same job. Full specifications are listed in the Additional information tab above.

Not sure this is your size? Run our free trash chute door fit check or call 203-304-9000 before you order.

References: MB1515, 1515SH, SH1515, SHU1515

Order This Right Hand Chute Door

Do you need help confirming fit? First, our team checks your opening size and hinge side. Then we guide your order. So call us at 203-304-9000 and we will help you pick the right part quickly.

This door replaces Midland, US Chutes, and Wilkinson Hi-Rise chute doors. We also build custom solutions for Acme Chutes, American Chute Systems, Century Chutes, Chutes International, Cutler Chutes, Hi-Rise Recycling Systems, Midland Metalcraft, Valiant Chutes, and Western Chutes. Simply contact us with your measurements for a custom quote.

The post 15″ x 15″ Right Hand – Side Hinged (SH) Chute Intake Door appeared first on Action Chutes.

This left hand chute door fits standard laundry and trash chute intakes. The unit hinges on the side, so it opens toward the left hand. Therefore it works well for new installs and for direct swaps of worn units.

No. 4 finish stainless steel forms the body. A border trim frames the opening. Also, the face shows no exposed welds or solder seams, so staff can wipe it clean in seconds. The front uses 20 gauge steel, while the back steps up to a heavier 18 gauge for strength, and we build every door in the USA.

Features Of This Intake Unit

Users open this unit by hand, and it then closes on its own. A keyed-alike cylinder lock secures it, while the latch holds it shut. Because the latch grabs each time, the panel stays closed after every use. Additionally, silent operation keeps hallway noise down.

Fire Rating

This panel carries a UL label, so it meets fire code needs. In fact, it holds a 1.5 hour rating with a UL Class B label at 250°F maximum temperature rise. In addition, our doors meet the latest national building codes, plus NFPA-82 and ASTM standards. However, you should always follow the manufacturer instructions and your local fire code when you install or service it.

Specifications For This Left Hand Chute Door

Overall dimensions for this side hinged intake door. Measure the cut-out in the chute wall, not the door panel and not the trim.

The stainless body resists rust and daily wear, and the keyed alike cylinder means one key opens every matching door on the same job. Full specifications are listed in the Additional information tab above.

Not sure this is your size? Run our free trash chute door fit check or call 203-304-9000 before you order.

References: MB1515, 1515SH, SH1515, SHU1515

Order This Left Hand Chute Door

Do you need help confirming fit? First, our team checks your opening size and hinge side. Then we guide your order. So call us at 203-304-9000 and we will help you pick the right part quickly.

This door replaces Midland, US Chutes, and Wilkinson Hi-Rise chute doors. We also build custom solutions for Acme Chutes, American Chute Systems, Century Chutes, Chutes International, Cutler Chutes, Hi-Rise Recycling Systems, Midland Metalcraft, Valiant Chutes, and Western Chutes. Simply contact us with your measurements for a custom quote.

The post 15″ x 15″ Left Hand – Side Hinged (SH) Chute Intake Door appeared first on Action Chutes.

This wall sleeve suits trash chute doors and laundry chute doors. It lines the opening as the door passes through the wall. Therefore it gives the assembly a clean, finished frame. Builders use it on both new installs and retrofits.

The sleeve is 16 gauge, and it uses aluminized steel. As a result, it resists rust and holds its shape over years of use. In addition, the sturdy build supports the door hardware well.

Where It Fits

This wall sleeve works with both bottom hinged and side hinged trash chute doors. Meanwhile, it handles a thru-wall depth of up to 12 inches. However, if your wall is deeper than that, call us and we will price a custom length for you.

Specifications

Here are the key details. First, the material is aluminized steel at 16 gauge. Next, the maximum thru-wall depth is 12 inches. Because it is a standard part, it ships quickly for most common openings.

How To Order The Right Size

Do you need help choosing the proper door size? First, measure your wall depth and door opening. Then compare those numbers to these specs. If you are unsure, our team can walk you through it step by step.

Lead Times And Contact

Parts often ship the same or next day, while doors take about two weeks from our warehouse. In addition, custom orders can take four to six weeks. So call us at 203-304-9000 and we will help you order the right wall sleeve quickly.

The post Wall Sleeve – Chute Door (Thru Wall) – Trash Chute Doors appeared first on Action Chutes.

This rubber baffle measures 15 inches wide by 18 inches high. It helps prevent back draft in your chute. Therefore it cuts down on odors that can draft back from the trash into your space. Building staff often add one to improve air quality on each floor.

The baffle uses thick rubber. Specifically, it is 1/8 inch thick, 60 Duro rubber, with a steel top assembly. As a result, it holds its shape and stands up to daily use in a busy chute.

Where It Fits

This part fits into your intake trash chute door. Meanwhile, it sits in the throat of the chute. Because it mounts out of sight, it does its job without changing how the door looks or opens.

Why Back Draft Matters

Back draft can be a major problem in high-rise buildings over ten stories. Air and odors can push back up toward the intake. However, the rubber baffle helps block that return path. So residents notice fewer smells at the door.

How To Order The Right Size

Do you need help choosing the correct door size? First, measure your existing door opening. Then compare it to your chute setup. If you are unsure, our team can walk you through it step by step.

Lead Times And Contact

Parts typically ship in about one week, while doors take roughly two weeks from our warehouse. In addition, custom orders can take four to six weeks. So call us at 203-304-9000 and we will help you order the right rubber baffle quickly.

The post Rubber Baffle for Back Draft for Trash Chute Door appeared first on Action Chutes.